Bending Derailleur Hanger

If not then the lateral distance per shift that the derailleur moves the chain will be less than the exact cog-to-cog spacing. As a rule of thumb if a hanger survives a repair by bending it will survive use.

Bent Derailleur Hanger Read My Tale Of Woe Richard Masoner Cyclelicious Flickr

Sure you might break the hanger bending it back into position.

Bending derailleur hanger. Cycle derailleur hangers are designed to bend and break. How to check the alignment of and if necessary adjust your rear derailleur hangerLook for your tools at Wiggle through our linkWiggle. A bent dreailleur will cause the chain to skip around on the gears.

Trying to get 8 seed derailleur working with a cheap bolt-on derailleur is doable but it wont shift very well and youll likely need to replace your QR axle with a solid nutted one to make the derailleur work at all. First my rear wheel isnt spinning freely and it also appears that my derailleur hanger is bending in. To check your work eyeball the alignment first and then thread your derailleur back into the hanger and use the policing cage as a guide that you can compare to the cogs above it.

Typically the derailleur hanger is supposed to be at right angles to the rear axle when seen from behind. A bent derailleur hanger can be cause by a bike falling on the drive side. In my case the brakes on my front wheel locked it flipping me over the handlebars.

Remove the derailleur from the hanger thread the axle into the hole as far as possible and you now have a nice little handle to gently bend the hanger. The reason hangers bend is to prevent the bending of your derailleur which unless youre still running alivio is by far more costly than replacing you hanger. Im not sure what exactly is causing this.

First judge how you believe the hanger to be bent. This is because there is very little stress from riding the bike or shifting gears. If you impact the derailleur hard enough to bend it you should keep reading farther down to understand how to replace it.

Check out the video. Know that I know what this component is I thought Id explain the details of. Since the hanger is aluminum and most alignment tools are steel be careful getting the tool started you dont want to strip the hanger threads.

A brief overview of signs symptoms and repair - YouTube. I show how to make a cheap DIY derailleur hanger alignment gauge similar to Park Tools DAG 22. I discovered that when my skewer lever is open the derailleur hanger looks straight and when I close the lever the hanger bends in.

But how much use is the bike if you cant fit a derailleur. The more common problem with bent derailleur hangers is that indexed shifting systems require the hanger to be parallel to the plane of the rear wheel. It is often possible to repeatedly re-bend many derailleur hangers.

I suspect the hanger might be warped or. We often see bent derailleur hanger in kids bicycles mountain bikes and sometimes road bikes. This pushes the derailleur body inward bending the hanger.

Then take hold of the upper part of the derailleur with both hands cupping it right around the back to give the derailleur as much support as. The next two photos show the basic steps for checking and fixing a bent derailleur hanger with the most common type of tools for the job. This tool is used to straighten and align a bent derailleur.

The basic alignment procedure with a proper tool. On most bikes this is a replaceable piece of aluminum which is designed to bend or break when stressed rather than causing costly damage to your frame. This inherent design actually keeps more expensive damage to your frame from occurring.

Basically the alignment of the chain. If these were stronger and more resistant to bending and breaking there is a good chance that these forces would bypass the hangers and destroy the area of the frame attached to the hangers. Inspection of the bike afterwards saw relatively minor damage to the handlebar grip the saddle and the point where the rear derailleur is.

Bent Bicycle Derailleur Hanger. If the bolt for the derailleur mount gets bent you wont be able to thread your tderailleur back into the hanger. Make sure the threaded end of the hollow axle are the same thread pitch as your hanger where the derailleur screws into the hanger.

The derailleur hanger is the piece of metal that the rear derailleur attaches to near the rear axle. However there are some hangers that do not repair well. Bending adjusting and replacing a derailleur hanger.

Derailleur hangers are designed to be sacrificed but that also means theyre prone to bending which manifests as dodgy and inconsistent shifting that no. So what happens when you bend a MTB Hanger. A good rule of thumb is that if you cant adjust it properly that means something somewhere is either bent or a cable is getting stuck.

All in all these things cant be known for certain until you actually look at the derailleur and its hanger from the back and see if its bent or not. Any deviation from this line will cause your.

Bent Derailleur Hanger Bike Boo Boos